2 m² Tilepal Tile Backer Boards 6mm thick, including 36 washers and 36 screws
Stable, impervious 120 cm x 60 cm tile backer boards for wet areas, including screws and washers
Tilepal See parts included Technical specificationFor the convenience of our clients, we have created tile backer board sets. The sets can cover up to 2 m², 4 m², 6 m² or 8 m² and include appropriate amount of washers and mounting screws. You can also choose boards thickness between 6 mm, 10 mm or 20 mm. Tile backer boards creates the perfect substrate to tile onto in wet rooms and bathrooms. Tilepal boards are made out of extruded polystyrene rigid foam and reinforced with glass fiber on both sides and coated with a elastic cement mortar.
Cement boards are lightweight and strong at the same time. They also have excellent insulating properties, so they work perfectly with an electric underfloor heating. Boards are 1200 x 600 mm and can be cut easily. They create perfect surface for tile adhesives on floors and walls.
This set includes:
- 3 cement boards (6 mm thick) to cover 2 m²
- 36 zinc washers
- 36 drywall screws
- Thickness
- 6 mm
- Pack coverage
- 2 m²
Hello,
We are not working during weekends, sometimes we do reply to emails and phone calls.
You can visit our Rotherham warehouse from Monday to Friday, 9am - 6 pm.
Let me know if you have any questions about our products or service.
Kind regards
Adam 017 0927 3601
Dear Customer,
Yes you can fix to a timber stud wall. You can use 10 or 12mm: 10mm - 300mm centres, 12mm - 400mm centres.
I am happy to assist if you have any questions.
Kind regards
Dear Lawrence,
I understand your concern. Please notice that while having the future floor level under the frame's height is not acceptable, having tiles sitting slightly above the frame is fine. Ideal situation is where tiles are sitting flushed with the frame.
There are 2 solutions:
- using multiple layer of tile adhesive. After first layer is dry you can apply another to build up height which will allow your mosaic tiles to be flushed with the drain's frame.
- using tile backer boards. You'd need to get 6 mm thick tile backer boards, cut them according to the slopes on the tray and fit them prior to finishing it with mosaic.
In both case the most important thing to do is not jeopardizing the slopes on top of the tray. There are diagonal slopes from every corner of the tray to every corner of the drain.
I am happy to assist if you have any further questions.
Kind regards
Dear Tom,
Thank you for being interested in our products. 1200 x 1200 would be fine shower tray for 1200 x 2300 mm wet room enclosed by a shower screen.
According to our fitting instructions, we recommend to remove floor boards, fix battens to the joints and mount at least 18 mm thick marine plywood in between the joints so the ply and joints are on the same level. Then you can fit the tray on top of that prepared supports.
In such case your tray just replace the floor board. If you want to use 18 mm thick backer boards on the remaining floor area I would recommend to go for 35 mm thick tray.
Kind regards
David M 020 7193 0953
Dear LJ,
No. Tile backer board cannot replace floor boards.
You should:
- remove existing floor boards
- fix battens to the sides of the joints
- mount at least 18 mm thick marine ply in between the joists on top of the battens
- cover newly created floor with tile backer boards and proceed to tiling
I am happy to assist if you have any questions.
Kind regards
Dear Jo,
Thank you for being interested in our products.
Tile backer boards can be stuck down to the floor with tile adhesive, however you need to use washers and screws to fix them to the walls.
I will be happy to assist if you have any questions.
David 020 7193 0953
Hello,
Yes, those boards are based on material which provides good insulation, can be used as boards for UFH.
They need to be laid on marine ply, are not strong enough to be installed without underboarding. You can install marine ply in between the joists (on the battens) though to avoid total floor height increase.
I will be happy to assist if you have any questions.
Kind regards
David 020 7193 0953
Hello Andy,
Thank you for your question.
Tilepal/Imperboard tile backer boards available in our offer at the moment are finished the same way on both sides, therefore it can be tiled over on either side.
I will be happy to help if you have any questions.
Kind regards
David 0113 543 1748